Cross Technologies 2015-26 Instruction Manual

Instruction Manual Model 2015-26 Upconverter December 2010 Rev. 0 MENUEXECUTEMODEL 2015CROSS TECHNOLOGIES INC. F=24

2.2 Rear Panel Input/Output Signals - Figure 2.2 shows the input and output connectors on the rear panel. ACGNDJ1810 MHZ REFOUTPUTJ10ANDMONITORCON

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.MENUEXECUTE F=2475 G=+10.0MUTE REMOTE POWERLCD

2.4 Operation2.4.1 Installing and Operating the 2015-26 Upconverter1. Connect a -10 dBm to -40 dBm signal to IF In, J4 (Figure 2.2)2. Connect the RF

2.5 Menu Settings2.5.1 FunctionsThis section describes operation of the front panel controls. There are three operator switches, the LCD display

2.5.2 Power On SettingsNOTE: THE LAST STATUS OF A UNIT IS RETAINED EVEN WHEN POWER IS REMOVED. WHEN POWER IS RESTORED, THE UNIT WILL RETURN TO IT&ap

2.5.4 Frequency ChangesAt any time during the modification process, if you have made a mistake and do not wish to save the changes you have made, d

2.5.5 Gain ChangesWhen you get to this menu note that the gain changes will be made as you make them but if you do not wish to save the changes you h

2.5.5 Alarm IndicationsAn alarm condition for will occur if any local oscillator phase lock loop (PLL) comes out of lock.The Mute LED will light if y

2.6 Available Options (Models: 2015-XX, 2016-XX & 2017-XX) LNB Voltage + 24 VDC, 0.4 Amps, for 2016-XX Downconverter. 2015-XX 2016-XX L Exte

Redundant Power Supply, for 2015, 2016 & 2017-XX Frequency Converters. NOT AVAILABLE on units with SSPB Power Option (Option V). 2015-XX 2016-X

INSTRUCTION MANUALMODEL 2015-26 Upconverter TABLE OF CONTENTS PAGEWarranty 21.0 General 31.1 Equipment Description 31.2 Technical Characteris

100 KHz Step Size for 2015-XX, 2016 -XX and 2017-XX Frequency Converters. 2015/16/17-XX X1 Option X - 125 KHz Step Size for 2015-XX or 2016 -XX Freq

CROSS TECHNOLOGIES, INC.6170 Shiloh RoadAlpharetta, Georgia 30005(770) 886-8005FAX (770) 886-7964Toll Free 888-900-5588WEB www.crosstechnologies.com E

MODEL 2015-26 Upconverter1.0 General1.1 Equipment DescriptionThe 2015-26 Upconverter converts 140 ± 36 MHz to 2000 to 2500 MHz in 1.0 MHz steps (0.5

1.2 Technical CharacteristicsTABLE 1.0 2015-26 Upconverter Specifications*Input Characteristics Impedance/Return Loss 75  /18 dBFrequency 140

1.3 Monitor and Control InterfaceA) Remote Serial InterfaceProtocol - RS-485, RS-422 or RS-232C (selectable), 9600 baud rate, no parity, 8 data bits,

B) Status Requests - Table 1.1 lists the status requests for the 2015-26 and briefly describes them.* PLEASE NOTE: The two character {aa}(00-31) prefi

C) Commands Table 1.2 lists the commands for the 2015-26 and briefly describes them. After a command is sent the 2015-26 sends a return “>” indic

1.4 Environmental Use InformationA. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions located in the u

2.0 Installation2.1 Mechanical - The 2015-26 consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A switchi